If water is still sitting around your house hours after the rain has stopped, there’s a good chance a blocked stormwater drain is behind it. It’s one of the most common drainage problems in Melbourne homes, and one we see a lot after a heavy downpour.
The good news is that it’s usually fixable, and in some cases you can sort it yourself. At O’Shea Plumbing, we clear and repair stormwater drains right across Melbourne, so here’s what you need to know about why it happens, what you can check and when it’s time to call us.
How does a stormwater system work?
Your stormwater system is there to move rain away from your home. Water runs off the roof into the gutters, drops down the downpipes and flows through underground pipes and pits on your property. From there, it heads out to the kerb or a council drain and eventually into local creeks and the bay.
It’s a simple setup, and when it’s working, you’ll barely notice it. But if any part of that path gets clogged, the water has to go somewhere. It backs up and settles in the lowest point it can find, which is why you’ll often see water pooling in the backyard, along paths or right up against the house.
What causes a blocked stormwater drain?
Sometimes, stormwater blockages in drains build up slowly over months or years, then show themselves all at once during a big storm. These are the causes we come across most often.
Leaves, silt and debris
This is the big one. Leaves from the gutters, soil washed off garden beds and dirt from paved areas all end up in your stormwater pipes. Over time, it settles and packs down until the pipe can’t carry the volume of water it needs to.
A blocked downpipe
A blocked downpipe is easy to miss because the problem is often hidden underground. Leaves collect in the bend where the downpipe meets the stormwater pipe, and once that fills up, water spills out of the joint or overflows from the gutter above. You might notice water gushing out at the base of the downpipe or a gutter overflowing even though it looks clean.
Tree roots
Roots are drawn to the moisture inside stormwater pipes. They find their way into small cracks and joints, particularly in older clay pipes, and grow into thick mats that catch everything flowing past. If you have established trees near your drainage lines, roots are worth considering.
Cracked or collapsed pipes
Ground movement, heavy vehicles and plain old age can crack or flatten a stormwater pipe. When that happens, water escapes into the soil around it rather than making its way to the street. That’s often why the same patch of lawn turns soggy every time it rains.
Gutter and roof problems
Damaged gutters, sagging sections and rusted joins can send water to the wrong places or wash more debris into the system. If your roof is part of the problem, our roof repairs team can fix the source so your drains aren’t working overtime.
Stormwater drain blocked? Here’s what you can check yourself
Before calling a plumber, there are a few simple things worth trying. They’re safe, quick and can save you a call-out if the fix is an easy one.
Start by watching your gutters during rain. If water is spilling over the edge rather than going down the downpipe, the gutter or the top of the downpipe is likely clogged. If you can reach a leaf guard or rainhead safely from a ladder, give it a clear out.
Next, lift the grates on your surface drains and stormwater pits. You’ll often find leaves, silt and rubbish sitting right at the top, and scooping it out with gloved hands can get things moving again.
Then try a hose test. Run a garden hose into a pit or the base of a downpipe and check whether water comes out at the kerb outlet. If it flows freely, that section is clear. If water rises back up the pit instead, the stormwater drain is blocked further along the line.
What to avoid
Please stay off the roof when it’s wet, and don’t push hired drain rods deep into the pipe. They can crack older clay lines or get stuck. And skip chemical drain cleaners altogether. They won’t shift roots or packed silt, and because stormwater isn’t treated, anything you pour in ends up in our creeks and waterways.
Is it your drain or the council’s?
This one comes up a lot. The gutters, downpipes and stormwater pipes on your property are your responsibility, right up to where they connect to the council system. The pits and drains out on the street are looked after by your local council.
If your hose test shows water flowing out freely at the kerb but the street drain is overflowing, it’s worth reporting to your council. If the problem is inside your boundary, that’s where we come in.
When should you call a plumber?
If you’ve done the basic checks and water is still pooling, the blockage is likely deeper in the pipe. It’s also time to call a plumber if a pit keeps refilling after you’ve cleared it, water is collecting around your home’s foundations or the ground is sinking along the line of a pipe.
A stormwater drain that blocks again a few weeks after clearing is another sign. That usually points to roots or a damaged pipe, and clearing the surface won’t fix it for long.
How we clear blocked stormwater drains
We start by working out exactly what’s going on. A CCTV drain camera lets us look inside the pipe, so we know whether we’re dealing with roots, silt or a broken section before we start.
From there, high pressure water jetting usually does the job. It scours the inside of the pipe and cuts through roots, leaving it clean and flowing properly. If the camera shows damage, we’ll talk you through your repair options and what each one involves. You can read more about how we handle blocked drains in Melbourne, from stormwater lines through to sewer pipes.
Book a drain check
If water keeps pooling around your home after rain, it’s worth finding out why before it starts affecting your foundations, paving or garden. Get in touch with O’Shea Plumbing to book a drain check, and we’ll find where the problem is coming from and get your stormwater flowing the right way again.